Contact : +33 1 41 23 50 23 (9:00 – 17:00 CEST)

Type 1+2+3 AC surge protector - Unipolar

DACN1-25VGS-10-440
Part Number 29221022
DACN1-25VGS-10-440
Availability:
€214.00 (excl. tax)

Available within 3 weeks

  • Type 1 + 2+3 AC surge protector
  • VG Technology
  • In: 25 kA
  • Iimp: 25 kA on 10/350µs impulse
  • No leakage current
  • Unpluggable module for each phase
  • Remote signaling
  • Optimized to TOV
  • EN 61643-11, IEC 61643-11 complied

The DACN1-25VG is an extreme duty Type 1+2+3 SPD designed to protect AC powerline at the main switchboard of an installation equipped with lightning rod, and in wind turbines' application, the low-voltage side of transformer and power side of convertor is the typical application. Equipped with exclusive CITEL’s VG technology, the range achieves an high protection level, guaranteeing a maximum protection efficiency, a absence of follow and leakage currents, a simplification of use (no additional lightning arrester required) and a maximum lifetime.


SPD type
IEC

1+2+3

AC system

TN

Max. AC operating voltage
Uc

440 Vac

Max. load current @25°C
IL

100 A

Temporary Over Voltage (TOV) Characteristics - 5 sec.
Without disconnection
UT

580 Vac withstand

Temporary Over Voltage (TOV) Characteristics - 120 mn
Without disconnection or with safety disconnection
UT

770 Vac disconnection

Residual Current
Leakage current to Ground
Ipe

None

Follow current
If

None

Nominal discharge current
15 x 8/20 µs impulses
In

25 kA

Max. discharge current
max. withstand @ 8/20 µs by pole
Imax

70 kA

Total Maximum discharge current
max. total withstand @ 8/20 µs
Imax Total

140 kA

Impulse current by pole
max. withstand 10/350µs by pole
Iimp

25 kA

Withstand on Combination waveform IEC 61643-11
Class III test: 1.2/50µs - 8/20µs
Uoc

6 kV

Specific energy by pole
max. withstand 10/350 µs
W/R

156 kJ/ohm

Protection level
@ In (8/20µs) and @ 6 kV (1,2/50 µs)
Up

1.5 kV

Admissible short-circuit current
Isccr

50 000 A

Technology

VG Technology (MOV+GSG)

SPD configuration

Single phase

Connection to Network

By screw terminals: 6-35mm² / by bus

Format

1-pole modular box

Plugable

No

Mounting

Symmetrical rail 35 mm (EN 60715)

Housing material

Thermoplastic UL94 V-0

Operating temperature
Tu

-40/+85°C

Protection rating

IP20

Failsafe mode

Disconnection from AC network

Disconnection indicator

1 mechanical indicator - Red/Green

Remote signaling of disconnection

Output on changeover contact

Wiring for remote signaling

1.5 mm² max.

Max. Voltage/Current for remote signaling

250 V / 0.5 A (AC) / 30 V / 3 A (DC)

Dimensions

See diagram - 2TE (EN43880)

Weight

0.408 kg

Standards compliance

EN 61643-11 / IEC 61643-11

Thermal disconnector

Internal

Installation ground fault breaker

Type 'S' or delayed

Back-up protection device

Fuses type gG - 315 A