Contact : +33 1 41 23 50 23 (9:00 – 17:00 CEST)

Compact single-phase type 2 (or 3) surge protector - Monobloc

DACN10S-L11-150
Part Number 70112012
DACN10S-L11-150
Availability:
€60.00 (excl. tax)
Add to cart

Available within 3 weeks

  • Cost effective single-phase surge protector
  • Type 2+3 monobloc compact
  • In/Imax: 5 kA/10 kA
  • Max. load current: 16A
  • Disconnection + AC line cut
  • 2-port configuration (series mounting)
  • Remote signaling
  • EN 61643-11, IEC 61643-11 compliance
Contact Us
DACN10S-L AC surge protector is used for the 'secondary' protection of the single-phase networks against the surge voltages creating by lightning. Unlike the DACN10S, the DACN10S-L incorporates an in-line safety disconnection and double output connection. The DACN10S-L provides common and differential mode protection and features an LED colour change from green to red at end of life. The DACN10S-L surge protector series is a single module DINRail mounted device designed to be installed close to the equipment being protected; it will normally be connected ‘downstream’ of a Type 1/2 'primary' surge protector.
SPD type
IEC 2+3
Network
 120 V single-phase
AC system
 TT-TN
Max. AC operating voltage
Uc 150 Vac
Max. load current
@25°C
 IL 16 A
Temporary Over Voltage (TOV) Characteristics - 5 sec.
Without disconnection
 UT 180 Vac withstand
Temporary Over Voltage (TOV) Characteristics - 120 mn
Without disconnection or with safety disconnection
 UT 230 Vac disconnection
Temporary Over Voltage N/PE (TOV HT)
Without disconnection or with safety disconnection
 UT 1200 V/300A/200 ms breaker disconnection
Residual Current
Leakage current to Ground
 Ipe None
Nominal discharge current
15 x 8/20 µs impulses
 In 5 kA
Max. discharge current
max. withstand @ 8/20 µs by pole
 Imax 10 kA
Withstand on Combination waveform IEC 61643-11
Class III test: 1.2/50µs - 8/20µs
 Uoc 10 kV
Protection level L/N
@ In (8/20µs)
 Up L/N 0.7 kV
Protection level N/PE
@ In (8/20µs)
 Up N/PE 1.5 kV
Admissible short-circuit current
 Isccr 10 000 A
SPD configuration
 Single phase
Connection to Network
 By screw terminals: 1.5-10mm²
Plugable
 No
Mounting
 Symmetrical rail 35 mm (EN 60715)
Housing material
 Thermoplastic UL94 V-0
Operating temperature
 Tu -40/+85°C
Protection rating
 IP20
Outdoor application
 No
Failsafe mode
 Disconnection and AC line cut-off
Disconnection indicator
 Green LED OFF
Remote signaling of disconnection
 Output on changeover contact
Wiring for remote signaling
 1.5 mm² max.
Max. Voltage/Current for remote signaling
 250 V / 0.5 A (AC) / 30 V / 2 A (DC)
Dimensions
 See diagram - 1TE (EN43880)
Weight
 0.092 kg
Standards compliance
 IEC 61643-11 / EN 61643-11 / UL1449 ed.5
Thermal disconnector
 Internal
Installation ground fault breaker
 Type 'S' or delayed
Back-up protection device
Fuses type gG - 25A