Contact : +33 1 41 23 50 23 (9:00 – 17:00 CEST)

Compact single-phase type 2 (or 3) surge protector - Monobloc

DACN10S-20-150

Part Number 70113012

Available within 3 weeks

Cost effective single-phase surge protector
Type 2 or 3 monobloc compact
In/Imax: 5 kA/10 kA
Max. load current: 25A
2-port configuration (series mounting)
Remote signaling
EN 61643-11, IEC 61643-11, UL1449 ed.5 compliance

DACN10S AC surge protector is used for the 'secondary' protection of the single-phase networks against the surge voltages creating by lightning. DACN10S is equipped with an internal thermal safety which will disconnet the unit from the AC network in case of end of life. Regarding the failsafe mode this surge protector is equipped with the option of disconnection and AC line cut-off. This disconnection will be indicate by the turn on of the red led in the front. Very compact, the DACN10S surge protector must be installed close by the equipment to protect, downstream a 'primary' surge protector. DACN10S provides both a common and differential mode protection.

Select another reference:

Electrical Properties Mechanical Properties Norms Deconnector Schemas

SPD type	IEC	2 (or 3)
Network		120 V single-phase
AC system		TN
Max. AC operating voltage	Uc	150 Vac
Max. load current @25°C	IL	25 A
Temporary Over Voltage (TOV) Characteristics - 5 sec. Without disconnection	UT	335 Vac withstand
Temporary Over Voltage (TOV) Characteristics - 120 mn Without disconnection or with safety disconnection	UT	230 Vac disconnection
Temporary Over Voltage N/PE (TOV HT) Without disconnection or with safety disconnection	UT	1200 V/300A/200 ms breaker disconnection
Residual Current Leakage current to Ground	Ipe	None
Nominal discharge current 15 x 8/20 µs impulses	In	5 kA
Max. discharge current max. withstand @ 8/20 µs by pole	Imax	10 kA
Total Maximum discharge current max. total withstand @ 8/20 µs	Imax Total	20 kA
Withstand on Combination waveform IEC 61643-11 Class III test: 1.2/50µs - 8/20µs	Uoc	10 kV
Protection level N/PE @ In (8/20µs)	Up N/PE	0.7 kV
Protection level L/PE @ In (8/20µs)	Up L/PE	0.7 kV
Admissible short-circuit current	Isccr	10 000 A

SPD configuration		Single phase
Connection to Network		By screw terminals: 1.5-10mm²
Plugable		No
Mounting		Symmetrical rail 35 mm (EN 60715)
Housing material		Thermoplastic UL94 V-0
Operating temperature	Tu	-40/+85°C
Protection rating		IP20
Outdoor application		No
Failsafe mode		Disconnection from AC network
Disconnection indicator		Green LED OFF
Remote signaling of disconnection		output on NC contact
Wiring for remote signaling		1.5 mm² max.
Max. Voltage/Current for remote signaling		250 V / 0.5 A (AC) / 30 V / 2 A (DC)
Dimensions		See diagram - 1TE (EN43880)
Weight		0.0917 kg

Standards compliance

IEC 61643-11 / EN 61643-11 / UL1449 ed.5

Thermal disconnector		Internal
Installation ground fault breaker		Type 'S' or delayed
Back-up protection device		Fuses type gG - 25A

Description: Compact single-phase type 2 (or 3) surge protector - Monobloc
Standards compliance: IEC 61643-11 / EN 61643-11 / UL1449 ed.5
SPD configuration: Single phase
Remote signaling of disconnection: output on NC contact
SPD type : 2 (or 3)
Network: 120 V single-phase
AC system: TN
Max. AC operating voltage : 150 Vac
Residual Current : None
Max. discharge current : 10 kA
Total Maximum discharge current : 20 kA
Admissible short-circuit current: 10 000 A

CITEL
Reference: DACN10S-20-150
Part Number: 70113012
Or equivalent

Select your protection

Discover our new video!

Citel presents its new range AC and DC SPDs